This Crossfire Red Dot uses either a high or low mount on different platforms

Turn the windage turret clockwise to move the point of impact to the left.

Turn the elevation turret counterclockwise to raise the elevation.

Move the dials in the direction where you want the bullet’s point-of-impact to change.

Remove the turret cap, turn the adjustment dial using the raised bar on the cover or a coin.

1 MOA closely corresponds to one inch at 100 yards, 1/2 inch at 50 yards, 1/4 inch at 25 yards, and more Each small click moves the point-of-impact one Minute of Angle. This Crossfire Red Dot uses elevation and windage dials with audible clicks. The Crossfire is a no-nonsense sight for near any application. Not only does it look awesome but also, it has an included skeletonized lower 1/3 co-witness mount that provides a rock-solid and extremely lightweight platform for your red hot. The 2 MOA dot is quick to acquire in close-quarters scenarios while remaining fine enough to promote pin-point accuracy at an extended range. Vortex Optics Crossfire Red Dot Sight Gen II – 2 MOA Dotĭoes your rifle, shotgun or rimfire just need a simple point of aim and none of the frills? If so, this particular scope should be at the top of your list.

You can also get an optional riser mount for the correct height for rifles.

Tighten the clamp screw using the hex wrench

Press the Viper down and forward toward the muzzle.Make sure the clamp is fully down and hooked around the outside of the base.Attach the Viper to the Picatinny base rail, while doing this make sure the recoil lug is seated in the base groove solidly.Using the provided screws attach the low rail mount to the viper.When this Viper red dot gets to you, it will have a low rail mount that clamps to both a Weaver or Picatinny rail. Finally Re-tighten both lock screws after the adjustments.Then adjust dials up or down or left or right.

First loosen both Adjustment Lock Screws 1½ turns,.To adjust elevation and windage follow these steps This Viper has adjustable elevation and windage dials with 1 MOA mark. O-ring seals that prevent penetration of dust, debris, and moisture.Easy to access and manipulate power and illumination controls.Waterproof and shockproof construction ensures your riflescope is ready for all conditions.Fully multi-coated offering a wide unobstructed field of view.Super low profile making it perfect for handguns with cutout slides.This daylight bright red dot can do up to 150 hours at the highest setting and up to 30,000 hours in lower settings. The 6 MOA Dot Reticle is very effective in all light conditions. Its recessed 1 MOA windage and elevation adjustments are super clean, protected from incidental contact, and always at the ready. It gives shooters the simplicity and dot advantage of a dot sight, while co-witnessing with stock iron sights. This Viper Red Dot’s super-low mounting height makes it the perfect solution for handguns with cutout slides. Waterproof and shockproof construction make these red dots ready for all conditions and environments.īest Vortex Red Dot Scopes Vortex Optics Viper Red Dot Sight 6 MOA Dot With these red dots, you also get a hard-anodized finish for durability. The Armortek coatings on the lenses are also very effective in preventing the lenses from dirt, oil, and scratches. The lenses are fully multi-coated and ultra-clear lenses for a wide and unobstructed field of view. Just like the Vortex Scopes, these Vortex red dots are feature-rich. We will go through features, price, Adjustments, and Mounting. In this Vortex Red Dots Review/Best Vortex Red Dot Scopes Review, we will comprehensively go through the different Vortex Red dots available in the market. 2 Factors to Consider for the Best Vortex Red Dots.1.5 Vortex Optics SPARC Red Dot Sight Gen II – 2 MOA Dot.1.4 Vortex Optics Strikefire II Red Dot Sights/Bright Red Dot/Red or Green Dot.1.3 Vortex Optics Razor Red Dot Sights 3 MOA /6 MOA.1.2 Vortex Optics Crossfire Red Dot Sight Gen II – 2 MOA Dot.1.1 Vortex Optics Viper Red Dot Sight 6 MOA Dot.

Vortex viper red dot